LED CONNECTOR HOW TO
LED CONNECTOR INSTALL
LED CONNECTOR CODE

Make sure that the teeth are piercing up through the strips and that your wire is pressed into the grooves. If you experience any flicker from the strip or it fails to light up then there is likely a connection issue.You now have a solid connection to wires and can run them to your power source or to another section of strip!ĮZ ClickTight Connector Tips and Troubleshooting.If you’re having trouble with wires moving around, try first pushing the wires into the slots a little more so they do not move when you try to clip the cap down.For the wire side it is best to use a set of pliers to help click the connector down all the way, it takes some force! Once the wires are sitting above the grooves click the cap down.RGB connectors will have 4 wires as stated earlier. We use red for positive and black for negative.

LED CONNECTOR CODE

Make sure you color code your wires or make sure they all line up.

Make sure to lift the clear cover and slide the wires in as far as they can.

There is no need to strip the wires before connecting. These solderless connectors work best with 20 AWG stranded wire. Extreme pulling on the strip would obviously pull it out but other than that, this is a quality connection to your strip! *As a side note you do not need to remove the silicone from the Waterproof strips, some connectors require this but the EZ clicks do not! Connecting Strip Connector to Wire This should make for a solid connection that will last. I lifted the tab here to show you how the teeth pierce the copper connection points.

Once you click it down the teeth should pierce up through the bottom of the copper pads on the strip, making for a solid connection.

Once it is in as far as it will go, push the tab down making sure each side clicks into place.

Make sure to lift the clear plastic cover and slide the strip in until it hits the backstop, it should sit under the lowest clear tab as shown in the picture.The connector will have 2-4 sharp teeth sticking straight up, the strip will slide in above these teeth: The connectors are easy to connect onto a strip end that has been cut. They will not fit if you purchase the wrong connector, however, so please make sure you have the connector matched up to the right strip. The IP67 connectors sit taller as they account for the silicone covering which is the only difference between the two.

The only other option for the connectors is choosing IP67 if you have a waterproof strip or choosing the IP20 option if you have an IP20 strip. The strip-to-wire connectors are sold with 6 inch wire leads.įor both waterproof and non-waterproof strips!

Strip-to-Wire: Connect to your strip and run wires out the other end to run to your power source or to another strip light if you have a gap in your LED run.

Strip-to-Strip: Easily connect strips end to end to form a longer run.

There are both 2 and 4 pin versions of the following LED strip connectors: The 4 pin RGB connectors have one common positive line as well as a connection for each of the Red, Green and Blue color LEDs so that they can all be controlled separately to make an assortment of different colors. The 4 pin connectors are identical in size and shape to the 2-pin but include 4 pins that match up with the connection points on RGB (color changing) strip lights. They only require a two-port connection as they simply need one positive and one negative connection. The 2-pin LED strip connectors are used for single color strips. There are two different connection types for the EZ Click tight connectors for LED strip lights.

LED CONNECTOR HOW TO

In this tutorial, we will go over how to use the strip connectors properly, to their full potential. That is why LED strip light solderless connectors work wonders to make numerous connections with ease. While soldering is very reliable, it can take a lot of time if you have many different connections to make. In fact, here is a quick guide on soldering your LED connections. If you do have a soldering iron, or want to buy one, then we recommend soldering as the most reliable option. LED strip connectors provide a quick-connect solution that lets people avoid having to use a soldering iron.

Connect two strips together, end-to-end to make a longer length.

The LED strip connectors in this guide will help you to: Unfortunately, many mistakes are made within this step but the good news is that connection issues are simple to fix or avoid with the right strip connectors. If poor connections are made, lights will flicker, go off unexpectedly or worse, not work at all.

LED CONNECTOR INSTALL

To avoid damage and a lot of frustration, anyone planning to install LED strip lights should first know the best way to make connections to the strips.

Led connector